Categories

Hot Products

News

About The Daily Use Of The Wax Cleaning Car And How To Repair It?
Nov 02, 2018

 One of the more important links in the production of oil wells is to solve the problem of plugging and washing wells. This link is also a difficult factor in the production of oil wells. The wax cleaning vehicle is put into use to solve these factors, and its importance is self-evident. . Daily maintenance and repair of the wax cleaning vehicle is an important guarantee for the safe and economic operation of the wax cleaning vehicle, and is also the main way to extend and maintain the service life of the boiler.

First, the daily maintenance of the wax cleaning car

 Any vehicle can only be used for daily maintenance to ensure its service life. The mechanization of natural wax cleaning vehicles is to strengthen daily maintenance. The maintenance of the car is not as simple as simply repairing the vehicle. It must also be divided into two aspects: vehicle maintenance and boiler maintenance.One of the more important links in the production of oil wells is to solve the problem of plugging and washing wells. This link is also a difficult factor in the production of oil wells. The wax cleaning vehicle is put into use to solve these factors, and its importance is self-evident. . Daily maintenance and repair of the wax cleaning vehicle is an important guarantee for the safe and economic operation of the wax cleaning vehicle, and is also the main way to extend and maintain the service life of the boiler.

1.The daily maintenance of the wax cleaning car

 Any vehicle can only be used for daily maintenance to ensure its service life. The mechanization of natural wax cleaning vehicles is to strengthen daily maintenance. The maintenance of the car is not as simple as simply repairing the vehicle. It must also be divided into two aspects: vehicle maintenance and boiler maintenance.

2. Daily use and maintenance of three-cylinder plunger pump

①Preventive maintenance should be used in the wax removal vehicle, especially if the power end is to be used for preventive maintenance. When the inspection is carried out frequently, large and small faults may be checked in time, and the fault will be repaired in time.

②Lock the wire; after opening the cover of the power end, you must also check all the bolts. The inspector locks the wire, the guide bolts, the connecting rod bolts, and when everything is checked, tighten the bolts and also the outside. The wire is replaced and locked.

③ Gearbox; in this block, it is necessary to check whether the gears of large and small are seriously worn out, but there may be some spots on the gear during the running-in period. These spots have no life effect on the life of the gear.

④ Crossheads and guides; with the use of the machine, the crosshead and the guides must be worn, and the wear and tear should be observed daily. If abnormal wear is found, it should be replaced immediately to prevent the wear of these two components. Bearings and other parts are damaged.

⑤ Tappet; crosshead and tappet are connected by bolts, and looseness will occur with use. Therefore, check the connection bolts for looseness during daily use and maintenance. If there is any, replace it immediately and check it. Whether the area that should be sealed is sealed.

⑥ Clamps; daily need to check whether the bolts on the clamps are loose, it is necessary to replace them in time, check the clamps for damage, and replace them in time.

3. Lubrication system

 There are still many places where the pump is used in the wax removal car, so make sure it is well lubricated. Therefore, ensuring lubrication at any time can greatly extend the life of the pump and the length of trouble-free use.

① Lubricating oil pressure; When using the pump to work, always pay attention to the change of the oil pressure gauge, be sure to keep the oil pressure between 0.2~1Mpa.

② Lubricating oil position, oil pipe; must also check the hydraulic end tank and the power end tank oil level, must be kept above the oil level. When filling, adjust by cutoff/throttle. Also check the lubricating oil pipe at any time. Make sure that the oil pipe is unobstructed and intact. Check whether the oil hose and the gear oil pump are damaged or flattened, and check whether the oil head has oil leakage.

4. Repair the boiler

 It is necessary to repair the components on the wax cleaning vehicle in a timely manner, but it is also not easy to take care of the boiler, and timely use and repair to prevent malfunction. Its specific use and maintenance are reflected in the following aspects:

① Always pay attention to whether the connection between the upper and lower casings of the boiler is sealed or fastened, and there is no smoke leakage. If these phenomena occur, they must be dealt with in a timely manner. At the same time, we must always pay attention to the situation when the boiler is burning. It is normal for the smoke emitted from the chimney during the observation period. Observing the water level displayed by the boiler, it is absolutely impossible to allow the boiler to run out of water and dry, which is very likely to damage the boiler.

② And every time (1 to 2 months), the coil of the boiler should be tested with cold water once. The pressure of the pressure test is 25Mpa. Also check if the riot device is rusted. Use the soot blower to turn the plate. The tube surface area carbon blows away.

 The wax cleaning car is widely used in various aspects due to its convenient use and power. However, any machine needs good maintenance and maintenance to show the best use rate and long life. Therefore, it is necessary to carry out scientific and reasonable maintenance for the wax cleaning vehicle. Both the components and the boiler must be maintained in accordance with the instructions and maintenance technology, so that the wax cleaning vehicle can maximize the utilization rate in use.


  • QR CODE
  • facebook